Tech talks
Exchange Ideas, Share Tips, Ignite
Conversations
Join the Biscuit People community today, and
let's bake the world a better place, one cookie at a time!
Sort by
Show
27.04.2021
Hello everyone
We have faced the challenge of producing a fruit shortcake biscuit product that uses raisin slices. We have to cut the raisins into smaller pieces first, then pour them into the dough, and this is where the problem begins. Our problem...
27.04.2021
Hi everyone,
has any of you had any experience with encrusting machines? I am looking to buy one for small productions (~40 pieces/min)
I could find some produced in US and Germany, but their cost is almost double that of - say - those produced by...
22.04.2021
Hi,
I understand that Marie biscuit is a kind of hard dough. But is there any possibility of making Marie biscuit using soft dough method and yet could be sheeted similar to hard dough?
Heard that Regal Biscuits texture is super different than any...
20.04.2021
Hi everyone,
we are
making cream cracker for the first time. In our experiments we get a hard one that doesn't melt in your mouth; there was little air between the layers.
We would like to get a delicate layered texture, like«Mayora» - ROMA Crea...
15.04.2021
Dear all,
we baked biscuits for the first time. We start with a soft biscuit (two types with/without cocoa powder). We have a direct-fired oven, 40m long, with four-zone.
We faced with two problems:
-the line of unbaked dough in the middle of the...
13.04.2021
Our waffle cones always seem more crumblier in texture to those from Europe. We would like to develop a stronger cone to be able to cope with the rigors of modern-day transportation and handling.
Ingredient listing
Wheat Flour (Calcium Carbonat...
12.04.2021
Dears
Excuse-me for my fail. I put accept in a comment from Alfredo, but I don´t get solve the problem yet.
We don´t have an equilibrium between top/bottom for Soda Cracker in our equipament.
The principal problem is the same. I have a SODA with...
12.04.2021
How can we use flat wafer scrap other than recycle into the wafer filling?
09.04.2021
Hi and Good Day! :)
I am sourcing for Marie biscuit mould (hand held). Stamping and cutting to be done manually. I am located in Malaysia.
Feel free to drop some contacts here or PM.
Thank you in advance for your help :)
Regards,
Amye
Not nec...
01.04.2021
Hi All,
I'm looking for small quantities (less than a pallet) of household recyclable or biodegradable biscuit wrapping for use on a flow wrapper. The biscuit is a shortbread.
The current film is Oriented Polypropylene (OPP), 25 micron, 200mm width...
Your Moderator
Sara Han
Food technologist, currently part of the team at Biscuit People
15 biscuits
Top TechTalkers
Iain Davidson
Director, Baker Pacific
1,050 biscuits
Lutz Popper
Scientific Director
700 biscuits
Jos Vast
Managing Partner/ Founder/ Senior Bakery Consultant
530 biscuits
Santiago Marino
Biscuit Technology Consultant
525 biscuits
George W Wright
Bakery Consultant, International Food Processing Consultancy
405 biscuits
Jacob van Kogelenberg
40 years experience in packaging
400 biscuits
Jose Azevedo
Product Development Manager | Biscuit Expert | Subject Matter Expert
360 biscuits
Mrs Beyhan Ozenli
Bakery Consultant
355 biscuits
Evita Riviani Achmadi
Food Consultant | Raw Material, Product Development, Formulator, Packaging...
355 biscuits
Alfredo Pimper
The old biscuit man--Biscuit Foodchain from field to supermarket
350 biscuits
The score is based on the number of published articles (20 points for every approved article in Our Experts category ), number of resolved questions (10 points for every resolved question) and the number of asked questions (5 points for every asked question). The list is showing only top 10 biscuit industry experts.