answer caret-left caret-right close-large facebook hamburger linkedin mail password question repeat-password thumb triangle twitter username youtube circle-right trending search checkmark pin alert
Innovative leak detection technology benefits MAP quality control

Ishida’s revolutionary AirScan inline system for detecting leaks in MAP packs has greatly enhanced the quality control procedures, as well as reducing labour costs, for a new snack product from M-Back GmbH in Germany which is being produced for dairy giant Meggle.

The "Ofenschnecke" is a small puff pastry product that is available in two versions, filled with a combination of feta cheese and fresh herbs or spinach. The rolls, which need to be warmed up in the oven before consumption, are packed in thermoformed trays each containing two or three products, with fill weights of 180g and 300g.

When the delicate puff pastries are packed, it is not uncommon for product traces to get into the sealing area of the trays. This can result in leaks, which may cause protective gas to escape and draw in moisture. In rare cases, external factors can also cause holes in the film. If such defective packaging is not withheld from distribution, the shelf life can be significantly reduced and the product appearance can suffer.

"We used to perform a visual inspection of smaller batches", says Marcel Schwebler, Head of the packaging department at M-Back. "However, this process was no longer practical, as output had increased significantly. So we looked for a fully automatic quality control solution that is 100% reliable."

Ishida AirScan uses laser technology to detect leaks of carbon dioxide (CO2), which is used in many MAP applications. The high-performance system checks each individual tray in less than 20 milliseconds for traces of escaping CO2.

It can reliably find holes with a diameter as small as 0.25 mm, at breath-taking speeds of up to 180 packs per minute. Users will improve their product quality without any adverse impact on products, as the inspection process does not exert any pressure - unlike conventional inline seal testers - and is therefore completely non-destructive. The inline system can be integrated into existing packing lines in a few minutes, without requiring any modifications to existing conveyors.


Ishida M back front view of Airscan showing reject bin below

The Ishida AirScan at M-Back has been placed at the end of the packing line, between other control systems and a labeller. Since its installation, quality assurance has reached new levels. About 3% of packs are identified as having a leak. These are eliminated using an air reject mechanism and transported to a collection chamber for subsequent repacking. M-Back's specification was to reliably identify leaks with a diameter of 0.4 mm or above, and compliance with this is regularly monitored by inserting a needle of the relevant size into packs and testing them. "But we definitely find even smaller holes," Marcel Schwebler reports. "By way of illustration, if you immerse the packs that have been found to be faulty in a water bath, you won't see any gas coming out. In a laboratory, however, we can detect changes in the composition of the gas mixture."

In two-shift mode, the Ishida AirScan checks 3,500 packs of "Ofenschnecken" per hour, which equates to a belt speed of 30 metres per minute. "There's no alternative to the AirScan system when it comes to speed," says Marcel Schwebler. He also highlights the system's user-friendliness and availability, pointing out that it is very easy and safe to operate and requires only minimum maintenance. No changes to settings are needed for product changeovers; only the height-adjustable control arm with the sensor head needs to be adjusted to the different pack heights. Dry cleaning before and after each production batch is completed within ten minutes.

The production data collected can be printed out as shift reports. M-Back also wants to connect the Ishida AirScan system to production analysis software in future. As well as the improvement in quality there is a significant reduction in labour costs, as the two employees who were previously required for visual inspection are now available for other tasks.

Marcel Schwebler's verdict is correspondingly positive: "The Ishida AirScan inline leak detection system is worth its weight in gold to us!"

Want to know more?
Ask industry experts in Biscuit People TechTalks section.
Read more from News
Read all
CIUS welcomes the End of the Sugar and Isoglucose Quota Regime
in
News
CIUS welcomes the end to market-distorting sugar production quotas. They have for too long, hampered the competitiveness of the European sugar-using f...
Ishida Europe celebrates 20 years of UK manufacturing
in
News
Packing line solutions specialist Ishida Europe is celebrating 20 years of manufacturing in the UK.
Natural flavourings in demand as commodity prices rocket
in
News
International Taste Solutions (ITS) says that it is seeing rising demand for its cost-effective natural flavourings as commodity prices rocket.